Codonics Virtua Manual de usuario descargar pdf (Pagina 3)



17991 Englewood Drive

Middleburg Heights, OH 44130

USA

+1.440.243.1198

+1.440.243.1334 Fax

Email info@codonics.com

www.codonics.com

Get it all with just one call

800.444.1198

All registered and unregistered trademarks are the property of their respective

owners. Specifications subject to change without notice. Patents pending.

Codonics Limited KK

AQUACITY 9F

4-16-23, Shibaura

Minato-ku, Tokyo, 108-0023

JAPAN

Phone: 81-3-5730-2297

Fax: 81-3-5730-2295

håçïå=`çããçå=fëëìÉë=

This section details common issues with Version 4.1.0

software that are likely to be experienced by most users.

◆

Changing ink cartridges without using the Ink

Cartridge Load button on the top of the Recorder may

cause a label with poor quality on the first disc printed

with the new cartridges.

To prevent this issue, press the

Ink Cartridge Load button before removing old ink

cartridges or an old print head. This issue applies only to

newer engines that use separate ink cartridges for each

color.

◆

Studies can be lost or corrupted if a hard power down

occurs.

Loss of power during some operations can result

in lost or corrupt data. An uninterruptible power supply

and proper shutdown procedure are strongly

recommended.

◆

Compatibility problems with Internet Explorer

7 or

greater and Firefox

There are minor cosmetic

problems when remotely connecting with both browsers.

Internet Explorer 6 is recommended for remote

connections to Virtua.

◆

Discs-required counts are inaccurate for multi-disc

backup jobs.

When multi-disc backup jobs (all studies

included in the job will not fit on one disc) are queued,

the

Discs Required

count in the

Status Details

tab and

the X of Y discs-recorded count on the

Discs

tab may

contain inaccurate counts. Typically, the count will not

increment until the entire set is completed.

håçïå=råÅçããçå=fëëìÉë

This section details uncommon or obscure issues with

Version 4.0.0 software that are unlikely to be experienced by

most users.

◆

Virtua may stop processing jobs and an error dialog

may appear on the touch screen.

Pressing OK on the

error dialog will allow the system to continue processing

jobs. Discs that were in-process may be ejected without a

printed label but will automatically be rerecorded and

reprinted.

◆

Process may stop during software installation.

Leaving

the network cable connected may cause installation to

stop during Phase 4. Disconnect cable prior to

installation.

◆

DICOM association limit may be exceeded.

DICOM

clients that open many simultaneous associations might

exceed Virtua’s limit of 24 simultaneous connections.

This can cause the system to stop receiving DICOM jobs,

requiring the system to be rebooted.

◆

Time-remaining indicators for jobs are inaccurate if

there is more than one Jobs page.

If there is more than

one page of jobs queued (eight or more jobs), the time-

remaining indicator on the

Discs

tab will not be accurate

on any pages other than the first page. Each page starts

the time-estimation over again without accounting for

the jobs on the previous page.

◆

Special handling for Recorder cover when installing

software on the Virtua ECO family systems

. When

media Smart Detect mode is enabled, leave the Recorder

cover open when installing software. Closing the cover

with Smart Detect mode enabled will cause Virtua ECO

to load another disc on top of the installation disc.

◆

The LaunchPad does not work on Windows NT

Windows 98

or Windows 2000

OS with Internet

Explorer version lower than 5.5.

When discs created on

Virtua are installed on PCs, the LaunchPad is initiated.

The LaunchPad can be used on Windows

2000/XP/Vista

and Windows ME

with Internet

Explorer v5.5 or higher. Users of affected platforms can

use Windows Explorer to navigate to and launch viewers

or open reports.

◆

Virtua ECO family system CD and DVD status lights

unexpectedly alternate green and off for longer than

two minutes.

In some circumstances, Virtua ECO may

show an unexpected shutdown taking longer than two

minutes. The workaround is to perform a hard shutdown

(press the System power button for about five seconds).

Power on the system to return to normal operations

when desired.

◆

IP address conflict is not reported.

If Virtua is

configured to support a range of IP addresses and there

is a conflict, Virtua will not notify the user.

◆

Successfully archived studies not marked as archived.

Aborting a Scheduled Archive while a label is being

printed may not mark studies successfully archived as

archived. Studies will be re-archived during the next

Scheduled Archive session.

håçïå=fëëìÉë=Ñçê=fåíÉêå~íáçå~ä=oÉÖáçåë

◆

No Unicode support in Viewer.

The Clarity Medical

Image Viewer does not correctly display Unicode

characters. It is uncommon for DICOM files to be

encoded in Unicode.

◆

Limited Viewer support for international characters.

Refer to the Clarity Viewer User’s Manual (Codonics Part

No. CLARITY-MNLU) for details.

◆

No support for Indian locales.

The Tamil, India (

ta_IN

)

locale does not correctly support Tamil characters.

◆

Site phone numbers with country codes may be

truncated on labels

. Most labels support nine characters

for phone numbers for the site details. The Ink Saver

label displays more characters.

◆

Cannot set date and time from Virtua user interface in

some Tier 2 locales.

The workaround for this problem is

to run the system in the en_US locale (which is the

factory setting), set the local time and date correctly, and

then change the system to the desired operating locale. A

list of Tier 2 locales and instructions for changing the

locale are in the Virtua User’s Manual.

qÉÅÜåáÅ~ä=pìééçêí

If problems occur during software installation, contact

Codonics Technical Support between the hours of 8:30AM

and 5:30PM EST (weekends and U.S. holidays excluded).

Phone: +1.440.243.1198

Email: support@codonics.com

Website: www.codonics.com

1 2 3

Comentarios a estos manuales

Sin comentarios

Codonics Virtua Manual de usuario Pagina 3

Comentarios a estos manuales